We don't give up the high standarts
HOMEPAGE
CORPORATE
QUALITY
PRODUCTS
REFERENCES
NEWS
TECHNICAL SPECIFICATIONS
CAREER
CONTACT

CLAMPS

GENERAL FEATURES

  •  High strength is provided by the help of the dual-shaped body.
  • Safe and easy ear connection is enabled by the radial combi and hexagonal  connection nuts.
  • Plastic slug is used for the nuts not to fall off  during the transportation and assembly.
  • 8-12 microns zinc is galvanized against rust.
  • By the EPDM caoutchouc izolation rubber ; noise reduction uptill 15 Db due to DIN 4109, assimilation of vibration and partial aspiration against the thermal expansions in the system are provided.

PIPE CLAMP WITH NUT

  • Standart nut is used for the hanger connection. 
  • Much more better nut welding is gained by the welding parts.

PIPE CLAMP WITH COMBI NUT

  • M8 and M10 connection is enabled by means of the combi nut used for the hanger connection.

PIPE CLAMP WITH NUT (STAINLESS STEEL)

  • DIN 1,4301 A2 stainless material is used.
  • Standart stainless nut is used for the hanger connection.

PIPE CLAMP WITH TRIPHONE

  • Triphon is used for the hanger connection.

PIPE CLAMP WITH LONG TRIPHONE

  • Long triphon is used for the hanger connection.

HEAVY DUTY PIPE CLAMP WITH HEAD

  • Head component is used for the hanger connection.

HEAVY DUTY PIPE CLAMP WITH MUFF

  • Cuff is used for the connection of the suspension.

SPRINGLER PIPE CLAMP

  • Hanging height can be set as desired with rods.

VENTILATION PIPE CLAMP (WITH NUT)

  • Standart nut is used for the hanger connection.

VENTILATION PIPE CLAMP (WITH SIDE HANGER)

  • Hanger connection is done by means of connecting the rods to the ears.

SOLAR PIPE CLAMP

  • Combi nut is used for the hanger connection.

SQUARE PIPE CLAMP - WITH BASE/WITHOUT BASE

  • Hanger connection is done directly to the assembly ground from the ear parts.

CHIMNEY PIPE CLAMP

  • Has an informal body structure.

HEAVY DUTY PIPE CLAMP WITH WIDE HEAD

  • By means of the thick and wide  plate structure, has the capacity of carrying very heavy loads.
  • Shall be used for the fixed or dynamic pipe sysyems.
  • Shall easily be used at all kinds of heat isolation areas together with the isolation block.
  • As well as having been enabling  safe connection with the hexagonal  connection nuts and bolts, arbitrarily without setting the connection hole enables connection by means of effectively welding the direct ears to each other.
  • Upon request, can be produced as head welded or without the head component.
  • Upon request, can be used  with EPDM caoutchouc izolation rubber.

SUSPENSION PARTS AND OTHER PRODUCTS

PERFORATED CANAL

  • Enables easy and safe asembly.

POLYURETHANE ISOLATION BLOCK

  • Generally is produced in 80 kg/m3 density. Upon request, may also be produced in higher densities.
  • Shall be used in between -150 oC and + 170oC.
  • Even in lower densities, high isolation is to be gained.
  • When compared with the other isolation materials, it is the lowest heat conductive material.
  • Has a long life.

SLIDING HINGE

  • Assembled generally onto the consoles and canals.

SLIDING BRAKE SHOE

  • Produced of the material POLIAMID 6 (NYLON 6).
  • In the horizontal connections, enables the connection of the pipes fom the top and as well as from the bottom.
  • Shall also be used for the vertical pipe connections.
  • The usage distance of the sliding blocks is limited with the length of the canal profile to be used.

VIBRATION BLOCK

  • Produced of the material EPDM.
  • Noise reduction uptill 18 Db and assimilation of vibration is enabled.

G CLIPS / VENTILATION CLAMP

  • Has the speciality of being able of easily fixing the profiles by the help of the nuts.
  • Has easy assembly possibility.
  • Has high loading capacity by means of its hard structure.
  • The clamp bolt has always to be suitable and in the same sizes with the flange bolts in order the assembly being able to carry by the same pushing value.

PROFILE HANGER CLAMP

  • Produced of the EN-GCS-450-10 material produced.
  • Enables fixing opportunity without welding or digging any holes on the beams.
  • Enables alignment opportunity at the bottom of the beams.
  • Enables hanging opportunity for the pipe clamps by the usage of rods.
  • Has high loading capacity.
  • Has fast height regulation opportunity.

SCREW ROD

  • Produced of the standart 6.8 quality material. Upon request may also be produced of 8.8 quality or stainless material too.

DRAW-IN ANCHOR (S TYPE)

  • Enables usage possibility with normal nuts and  stabs.
  • Has high pull strength by means of balanced and non-sliding structure due to the fded atriums at the applied hole.
  • If nuts will be used, size is to be cared of.
  • In stab usage, slug and nut height has to be taken intoconsideration.

BASE PLATE

  • If has been requested, may also be produced as with nut or with muff. 
  • The connection may be done by rod on the nut ground plate and by nipple adaptor part by muff.
  • Provides assembly opportunity for all kinds of grounds or canals.

CEILING SUSPENSION ANCHOR

  • Enables fast and secure assembly opportunity by means of its small hole depth and small hole diameter.

DROP-IN ANCHOR

  • Can be used at short hole depths and hard concrete grounds.
  • Enables balanced expanding and ground catching opportunity by the help of the conical core inside of the plug.

EXTENSION NUT

  • Lock-nut shall be used for mounting.
  • The minimum screwdriving length shall be as to thread diameter.

HEAVY DUTY ANCHOR

  • By means of the high pull strength, enables a safe connection.
  • By means of thespecial form in the used pieces, the wings enable a balanced load distribution.
  • Used with hexagonal nuts.
  • May be used with stab and nut.

HOOK SUSPENSION ANCHOR

  • Enables quick and easy assembly.
  • Safe holding and pressing speciality is gained by means of fast and easy openable tunicate structure.
  • May easily be used in short holes and vibrational areas.

MONOCLIP ANCHOR

  • Stable for hanging loads.
  • Because of the diameter of the plug is equal to the diameter of the drill to be used, it is economical. 
  • Has the opportunity of quick and easy assembly.

NEOPRENE SEAL

  • Produced of the material NEOPREN (NE).
  • By means of its sticky surface, enabes easy implementation possibility.

PIPE TYPE ANCHOR

  • Plug tube has been produced of IDGM type pipe.

PLASTIC ANCHOR

  • Enables easy and safe assembly.
  • By means of the quality of the plastic which has been used, breaking, cracking and plication will not be found during the implementation.
  • Suitable peg screw as to the peg measure has to be used.
  • For a safe and correct implementation, diameter of the hole has to be digged due to the given value.

SLEEVE ANCHOR

  • Safe holding and pressing speciality is gained by means of fast and easy openable tunicate structure.
  • May easily be used in short holes and vibrational areas.
  • Enables digging and assembling opportunity by the component shall have to be installed.

TRIPHONE ADAPTER

  • Produced as one side from metric jag and the other side from triphon jag(peg screw, wood screw).